Standard Wood Dock Hardware 42 Products
from
$6.50
WD-HOPH3 — WD-HOPH3B
Weight: 8.00 LBS - 3 inch Pipe Holder Weight: 2.00 LBS - Backup Plate
Use with 1-1/2" or 2" Pipe
NOTE: Pipe holder and backup plate must be purchased separately below. They do not come as a pair.
from
$8.50
WD-PH3S — WD-PH3SB
Weight: 13.00 LBS - Split 3 inch Pipe Holder Weight: 4.00 LBS - Backup Plate
NOTE: Pipe holder and backup plate must be purchased separately below. They do not come as a pair.
from
$12.50
WD-PH5 — WD-PH5B
Weight: 10.00 LBS - 5 inch Pipe Holder Weight: 4.00 LBS - Backup Plate
Use with 3" - 4" O.D. Pipe
from
$12.50
WD-PH5S — WD-PH5B
Weight: 13.00 LBS - Split 5 inch Pipe Holder Weight: 4.00 LBS - Backup Plate
NOTE: Pipe holder and backup plate must be purchased separately below. They do not come as a pair.
from
$136.50
WD-RCP3 — WD-RCP6
The ramp cover plates are designed to cover the gap created by the male/female hardware between the ramp and shore by providing a covered walking surface between the sections. One side is pre-punched and will bolt through the deck surface. The opposite side will slide with the movement of the...
from
$148.00
WD-BAR34 — WD-BAR56
Building a roller ramp has never been easier using our ramp roller kits. The outside roller brackets are backed up with our standard WD-E Outside Corner Ends and the center roller bracket is backed by our WD-W Washer Plates. Rollers included. The WD-BAR34 is for 3' to 4' ramps and...
$66.00
WD-RP1
Ideal for those areas where a sturdy roller assembly is needed. Weight: 13.5 LBS
Sold individually.
$17.50
WD-TF
Has two 1/2" tabs and is used with Outside Corner Male (WD-M) or Single T Male (WD-TM) connectors. Can be bolted to a seawall for hinging ramps or to the side of a dock for finger attachment. Weight: 3.5 LBS
$14.50
WD-TM
Has one 3/4" tab and is used with Outside Corner Female (WD-F) or Single T Female (WD-TF) connectors. The tabs are pre-drilled to accommodate a 3/4" pin or bolt. Weight: 3 LBS
$38.00
WD-44B
Our 4x4 Bracket attaches a 4x4 wood upright securely to the docks framing. Perfect for handrail. (4x4 post not included) Weight: 5.25 LBS
$25.50
WD-TFJB
This Special Single T Female allows a female connection where a cross stringer is present on a main dock as shown in the second image to the left. Use with (WD-M) Outside Corner Males. Weight: 3.75 LBS
Sold individually.
$79.50
WD-SP
Splice Plates are designed to join two side stringers together to make longer dock sections. The flat plate is used on the outside of the stringer, and the T plate is used on the inside of the stringer. The T plate will attach to the cross stringer as shown. Set...
from
$39.00
A-STM — A-STF
This is an affordable alternative to piling. Using our two Stiff Arm fittings you can make a stiffarm using 2" pipe. Each fitting thru bolts into a 2" pipe. The WD-STM thru bolts into each end of a 2" pipe and the WD-STF bolts into 2" pipe in the ground...
$2.00
WD-W
Washer Plates are used with Angles (WD-A) and Cleat Angles (WD-CA). The wood is sandwiched between the steel providing greater strength. Weight: 0.50 LBS
Sold individually.
$4.50
WD-W8
These 8" high Washer Plates are used with the 8" high Angles (WD-A8). The wood is sandwiched between the steel providing greater strength. Weight: 0.50 LBS
Sold individually.
$35.50
S-MP
Mud Pad goes on the end of 1.50" Schedule 10 pipe and allows mooring poles to sit on the muddy bottom. Can be used as supports or for extra footing.
Sold individually.
from
$1.50
F-PIN34 — F-HC16
Connector Pin and Hitch Clip available in various sizes. Hitch Clip and Flat Washer also sold separately in drop down menu below. F-PIN34 is used with Residential and Standard hardware F-PIN36 is used with Heavy Duty hardware F-PIN34 3/4" x 4" HDG Connector Pin & Hitch Clip F-PIN36 3/4" x...
