Hardware 59 Products
$4.25
WD-A
Used for attaching cross stringers to side stringers. Two Washer Plates (WD-W) are used with each Angle to sandwich lumber and provide a solid connection. Weight: 1.75 LBS
Sold individually.
$12.10
WD-A66
These longer Angles use two Backup Plates (WD-B) with each Angle to sandwich lumber and provide a solid connection. Weight: 1.75 LBS
Sold individually.
$8.80
WD-A8
This 8" tall Angle is perfect to use with larger framing. Each 8" Angle is backed by two 8" high Washer Plates (WD-W8). Weight: 3.50 LBS
Sold individually.
$32.35
S-A
Makes the job of anchoring and installing much easier. Made from cast aluminum.
Fits with 1 1/2" pipe, and fastens with 3/8" bolt
Weight: 1.50 LBS
$4.25
WD-B
5" x 5" x 1/4" Backup Plates are used to backup Single T Female (WD-TF) and Single T Male (WD-TM) connectors. The backup is also used for backing Chain Retainers (WD-CR). Weight: 1.75 LBS
Sold individually.
$7.45
WD-HDB
Heavy Duty Backup Plates are used to backup the (WD-HDTM) Single T Male and (WD-HDTF) Single T Female connectors. Weight: 2.25 LBS
Sold individually.
$11.55
WD-CR
These are typically bolted to the side of the dock or to a cross stringer and can accommodate up to 1/2" chain to hold the dock in place. Use a WD-B as a backup plate. There is also an XL Chain Retainer available. Weight: 3.75 LBS
Sold individually.
$22.30
WD-PHCR
A larger version of the Chain Retainer (WD-CR) that can accommodate up to 1/2" chain. Measures 5" tall with 9/16" slots. Inside dimensions are 4.25" x 3". These are typically bolted to the side of the dock and uses chain to hold the dock in place. Uses a WD-PHCRB as...
$10.20
WD-PHCRB
Backup Plate for Chain Retainer XL, measuring 7.75" x 7.25". Weight: 4.10 LBS
Sold individually.
$6.00
WD-CA
The Cleat Angle is bolted to the inside of the side stringer and uses a WD-W washer plate as a back up. The cleat is bolted through the deck and through the cleat angle. The slotted holes allow for various size cleats to be used. This cleat assembly ties your...
$6.90
WD-CAXL
The XL Cleat Angle is for cleats larger than 12". The Cleat Angle is bolted to the inside of the side stringer and uses a WD-W washer plate as a back up. The cleat is bolted through the deck and through the cleat angle. The slotted holes allow for various...
$4.15
WD-CAFW
The Cleat Flat Washer provides additional holding strength in areas a cleat angle cannot be used. Weight: 1.5 LBS
Sold individually.
$33.85
WD-FCP
Connector plate and pin for wood dock or Follansbee Blue Dock
Set includes (2) plates and (1) pin
from
$179.30
STF-FDS3 — STF-FDS4
Our welded truss Finger Deck Stabilizers really add stability to finger docks while providing a safe access onto the dock. Available in 3 ft. or 4 ft. sizes Weight: 48 LBS - 3 ft. Weight: 65 LBS - 4 ft.
+ TRUSS FRAME INFORMATION
from
$72.00
S3-3DB — S3-6DB
Dock Bracket is designed to be sturdy and easier to install. Bracket rests right under the metal channel dock frame, and the addition of welded pipe holders allows installing and securing the pipe easier. After brackets are set in the ground, you simply lay the metal box frame sections on...
$13.75
WD-FDS135
Using our WD-FDS45 and WD-FDS135, you can construct a finger deck stabilizer. This assembly helps stabilize narrow fingers by spreading the load onto the main dock. The WD-B Backup Plates are used as backups to the T (not included). Weight: 4.5 LBS
Sold individually.
$23.95
WD-FDS45
Using our WD-FDS45 and WD-FDS135, you can construct a finger deck stabilizer. This assembly helps stabilize narrow fingers by spreading the load onto the main dock. The WD-B Backup Plates are used as backups to the T (not included). Weight: 8.52 LBS
Sold individually.
$118.55
WD-FPS
Our pipe type finger dock stabilizer is an easy way to stabilize your finger dock. We use two WD-TF Single T Females, two WD-B Backup Plates, and 2" galvanized pipe. An F-PIN34 and Clip connect each end (included). Weight: 24 LBS
$77.07
STF-FS30
The finger stabilizer is an inexpensive way to add stability to your finger dock. It extends 30" down the dock. Weight: 21 LBS - 30"
from
$10.60
STF-DTM — F-PIN36
The double Male / Female plates allow you to pin truss dock sections together for easy installation and removal. STF-DTM - Male Plate - 6.67 lbs. STF-DTF - Female Plate - 7.32 lbs. F-PIN36 - Connector Pin - 1.16 lbs. Also available in a Standard Male/Female Plate option.
$17.50
WD-IN
Inside Corners with corner gussets are used as an inside backup for the Outside Corner hardware. The corner gusset provides strength and helps reduce racking. Weight: 6 LBS
Sold individually.
$34.40
WD-INPH3
Can be used to replace a standard inside corner. Has a 3" I.D. pipe welded into the corner providing internal anchoring. Accommodates 2" pipe. Weight: 17 LBS
Sold individually.
$5.50
WD-NAB
Backup Plates are used as a set to connect non-articulating finger docks into the side of main dock sections. Weight: 1.75 LBS
Sold individually.
$23.95
WD-TFD
Two holes allow for easy attachment and create a non-articulating hinge. The tabs are pre-drilled to accommodate a 3/4" pin or bolt.
Weight: 3.50 LBS
Sold individually.