Boat Dock Hardware 82 Products
The backbone of a better dock system. Explore our premium American-made hardware built for strength, stability, and long-term performance for every dock build.
$4.50
WD-A
Used for attaching cross stringers to side stringers. Two Washer Plates (WD-W) are used with each Angle to sandwich lumber and provide a solid connection. Weight: 1.75 LBS
Sold individually.
$13.00
WD-A66
These longer Angles use two Backup Plates (WD-B) with each Angle to sandwich lumber and provide a solid connection. Weight: 1.75 LBS
Sold individually.
$9.50
WD-A8
This 8" tall Angle is perfect to use with larger framing. Each 8" Angle is backed by two 8" high Washer Plates (WD-W8). Weight: 3.50 LBS
Sold individually.
$6.50
WD-CA
The Cleat Angle is bolted to the inside of the side stringer and uses a WD-W washer plate as a back up. The cleat is bolted through the deck and through the cleat angle. The slotted holes allow for various size cleats to be used. This cleat assembly ties your...
$7.50
WD-CAXL
The XL Cleat Angle is for cleats larger than 12". The Cleat Angle is bolted to the inside of the side stringer and uses a WD-W washer plate as a back up. The cleat is bolted through the deck and through the cleat angle. The slotted holes allow for various...
$25.00
WD-M
Has one 1.75" tab and is used with Outside Corner Female (WD-F) or Single T Female (WD-TF) connectors. The tabs are pre-drilled to accommodate a 3/4" pin or bolt. Weight: 8 LBS
Sold individually.
$28.50
WD-F
Has two 2.5" tabs and is used with Outside Corner Male (WD-M) or Single T Male (WD-TM) connectors. The tabs are pre-drilled to accomodate a 3/4" pin or bolt. Weight: 8.5 LBS
Sold individually.
$42.00
WD-SM
The Special Outside Corner Male allows a finger dock to be added at a corner of a main dock. Use with standard (WD-F) Outside Corner Females. Weight: 11.75 LBS
Sold individually.
$49.00
WD-SF
The Special Outside Corner Female allows a finger dock to be added at a corner of a main dock. Use with standard (WD-M) Outside Corner Males. Weight: 11.75 LBS
Sold individually.
$42.00
WD-SMF
The Special Outside Corner Male/Female allows a finger dock to be added at a corner of a main dock. Use with standard (WD-F) Outside Corner Females and (WD-M) Outside Corner Males. Weight: 11.75 LBS
Sold individually.
$17.00
WD-E
Outside Corner Ends are used at the end of docks, ends of finger docks, swim floats corners, or when plain ends are needed. Weight: 7 LBS
Sold individually.
$18.50
WD-IN
Inside Corners with corner gussets are used as an inside backup for the Outside Corner hardware. The corner gusset provides strength and helps reduce racking. Weight: 6 LBS
Sold individually.
$25.50
WD-FDS45
Using our WD-FDS45 and WD-FDS135, you can construct a finger deck stabilizer. This assembly helps stabilize narrow fingers by spreading the load onto the main dock. The WD-B Backup Plates are used as backups to the T (not included). Weight: 8.52 LBS
Sold individually.
$14.50
WD-FDS135
Using our WD-FDS45 and WD-FDS135, you can construct a finger deck stabilizer. This assembly helps stabilize narrow fingers by spreading the load onto the main dock. The WD-B Backup Plates are used as backups to the T (not included). Weight: 4.5 LBS
Sold individually.
$17.50
WD-TF
Has two 1/2" tabs and is used with Outside Corner Male (WD-M) or Single T Male (WD-TM) connectors. Can be bolted to a seawall for hinging ramps or to the side of a dock for finger attachment. Weight: 3.5 LBS
$14.50
WD-TM
Has one 3/4" tab and is used with Outside Corner Female (WD-F) or Single T Female (WD-TF) connectors. The tabs are pre-drilled to accommodate a 3/4" pin or bolt. Weight: 3 LBS
$2.00
WD-W
Washer Plates are used with Angles (WD-A) and Cleat Angles (WD-CA). The wood is sandwiched between the steel providing greater strength. Weight: 0.50 LBS
Sold individually.
$4.50
WD-W8
These 8" high Washer Plates are used with the 8" high Angles (WD-A8). The wood is sandwiched between the steel providing greater strength. Weight: 0.50 LBS
Sold individually.
$4.50
WD-CAFW
The Cleat Flat Washer provides additional holding strength in areas a cleat angle cannot be used. Weight: 1.5 LBS
Sold individually.
$4.50
WD-B
5" x 5" x 1/4" Backup Plates are used to backup Single T Female (WD-TF) and Single T Male (WD-TM) connectors. The backup is also used for backing Chain Retainers (WD-CR). Weight: 1.75 LBS
Sold individually.
$8.00
WD-HDB
Heavy Duty Backup Plates are used to backup the (WD-HDTM) Single T Male and (WD-HDTF) Single T Female connectors. Weight: 2.25 LBS
Sold individually.
$11.00
WD-PHCRB
Backup Plate for Chain Retainer XL, measuring 7.75" x 7.25". Weight: 4.10 LBS
Sold individually.
$31.00
WD-HDTM
Has two 3/4" tabs and is used with Heavy Duty Outside Corner Female (WD-HDF) or Heavy Duty Single T Female (WD-HDTF) connectors. The tabs are pre-drilled to accommodate a 3/4" pin or bolt. These are used where additional strength is needed. Uses a (WD-HDB) Backup Plate. Weight: 3.00 LBS Sold...
$36.50
WD-HDTF
Has three 1/2" tabs and is used with Heavy Duty Outside Corner Male (WD-HDM) or Heavy Duty Single T Male (WD-HDTM) connectors. Can be bolted to the side of a dock for finger attachment. These are used where additional strength is needed. Uses a (WD-HDB) Heavy Duty Backup Plate. Weight:...
