hardware

Angle

$4.50

WD-A

Used for attaching cross stringers to side stringers. Two Washer Plates (WD-W) are used with each Angle to sandwich lumber and provide a solid connection. Weight: 1.75 LBS Sold individually.

Angle - 6" x 6"

$13.00

WD-A66

These longer Angles use two Backup Plates (WD-B) with each Angle to sandwich lumber and provide a solid connection. Weight: 1.75 LBS Sold individually.

Angle - 8 inch

$9.50

WD-A8

This 8" tall Angle is perfect to use with larger framing. Each 8" Angle is backed by two 8" high Washer Plates (WD-W8). Weight: 3.50 LBS Sold individually.

Auger

$34.00

S-A

Makes the job of anchoring and installing much easier. Made from cast aluminum. Fits with 1 1/2" pipe, and fastens with 3/8" bolt Weight: 1.50 LBS

5" x 5" x 1/4" Backup Plates are used to backup Single T Female (WD-TF) and Single T Male (WD-TM) connectors. The backup is also used for backing Chain Retainers (WD-CR). Weight: 1.75 LBS Sold individually.

Backup Plate - Heavy Duty

$8.00

WD-HDB

Heavy Duty Backup Plates are used to backup the (WD-HDTM) Single T Male and (WD-HDTF) Single T Female connectors. Weight: 2.25 LBS Sold individually.

Chain Retainer

$12.50

WD-CR

These are typically bolted to the side of the dock or to a cross stringer and can accommodate up to 1/2" chain to hold the dock in place. Use a WD-B as a backup plate. There is also an XL Chain Retainer available. Weight: 3.75 LBS Sold individually.

Chain Retainer XL

$23.50

WD-PHCR

A larger version of the Chain Retainer (WD-CR) that can accommodate up to 1/2" chain. Measures 5" tall with 9/16" slots. Inside dimensions are 4.25" x 3". These are typically bolted to the side of the dock and uses chain to hold the dock in place. Uses a WD-PHCRB as...

Chain Retainer XL Backup Plate

$11.00

WD-PHCRB

Backup Plate for Chain Retainer XL, measuring 7.75" x 7.25". Weight: 4.10 LBS Sold individually.

Cleat Angle

$6.50

WD-CA

The Cleat Angle is bolted to the inside of the side stringer and uses a WD-W washer plate as a back up. The cleat is bolted through the deck and through the cleat angle. The slotted holes allow for various size cleats to be used. This cleat assembly ties your...

Cleat Angle XL

$7.50

WD-CAXL

The XL Cleat Angle is for cleats larger than 12". The Cleat Angle is bolted to the inside of the side stringer and uses a WD-W washer plate as a back up. The cleat is bolted through the deck and through the cleat angle. The slotted holes allow for various...

Cleat Flat Washer

$4.50

WD-CAFW

The Cleat Flat Washer provides additional holding strength in areas a cleat angle cannot be used. Weight: 1.5 LBS Sold individually.

Deck Stabilizer

from $188.50

STF-FDS3 — STF-FDS4

Our welded truss Finger Deck Stabilizers really add stability to finger docks while providing a safe access onto the dock. Available in 3 ft. or 4 ft. sizes Weight: 48 LBS - 3 ft. Weight: 65 LBS - 4 ft. + TRUSS FRAME INFORMATION

Finger Deck Stabilizer 135

$14.50

WD-FDS135

Using our WD-FDS45 and WD-FDS135, you can construct a finger deck stabilizer. This assembly helps stabilize narrow fingers by spreading the load onto the main dock. The WD-B Backup Plates are used as backups to the T (not included). Weight: 4.5 LBS Sold individually.

Finger Deck Stabilizer 45

$25.50

WD-FDS45

Using our WD-FDS45 and WD-FDS135, you can construct a finger deck stabilizer. This assembly helps stabilize narrow fingers by spreading the load onto the main dock. The WD-B Backup Plates are used as backups to the T (not included). Weight: 8.52 LBS Sold individually.

Finger Pipe Stabilizer

$124.50

WD-FPS

Our pipe type finger dock stabilizer is an easy way to stabilize your finger dock. We use two WD-TF Single T Females, two WD-B Backup Plates, and 2" galvanized pipe. An F-PIN34 and Clip connect each end (included). Weight: 24 LBS

Finger Stabilizer

$77.07

STF-FS30

The finger stabilizer is an inexpensive way to add stability to your finger dock. It extends 30" down the dock. Weight: 21 LBS - 30"

Hinge Connector Plates - Double

from $11.50

STF-DTM — F-PIN36

The double Male / Female plates allow you to pin truss dock sections together for easy installation and removal. STF-DTM - Male Plate - 6.67 lbs. STF-DTF - Female Plate - 7.32 lbs. F-PIN36 - Connector Pin - 1.16 lbs. Also available in a Standard Male/Female Plate option.

Inside Corner

$18.50

WD-IN

Inside Corners with corner gussets are used as an inside backup for the Outside Corner hardware. The corner gusset provides strength and helps reduce racking. Weight: 6 LBS Sold individually.

Inside Corner Pipe Holder

$36.50

WD-INPH3

Can be used to replace a standard inside corner. Has a 3" I.D. pipe welded into the corner providing internal anchoring. Accommodates 2" pipe. Weight: 17 LBS Sold individually.

Non-Articulating Double Pin Bracket Female

$25.50

WD-TFD

Two holes allow for easy attachment and create a non-articulating hinge. The tabs are pre-drilled to accommodate a 3/4" pin or bolt. Weight: 3.50 LBS Sold individually.

Non-Articulating Double Pin Bracket Male

$18.00

WD-TMD

Two holes allow for easy attachment and create a non-articulating hinge. The tabs are pre-drilled to accommodate a 3/4" pin or bolt. Weight: 3.00 LBS Sold individually.

Non-Articulating Double Pin Corner Female

$39.50

WD-NAFD

Two holes allow for easy attachment and create a non-articulating hinge. The tabs are pre-drilled to accommodate a 3/4" pin or bolt. Weight: 9.51 LBS Sold individually.

Non-Articulating Double Pin Corner Male

$32.50

WD-NAMD

Two holes allow for easy attachment and create a non-articulating hinge. The tabs are pre-drilled to accommodate a 3/4" pin or bolt. Weight: 9.25 LBS Sold individually.