Hardware 88 Products
$4.15
WD-CAFW
The Cleat Flat Washer provides additional holding strength in areas a cleat angle cannot be used. Weight: 1.5 LBS
Sold individually.
$22.30
WD-PHCR
A larger version of the Chain Retainer (WD-CR) that can accommodate up to 1/2" chain. Measures 5" tall with 9/16" slots. Inside dimensions are 4.25" x 3". These are typically bolted to the side of the dock and uses chain to hold the dock in place. Uses a WD-PHCRB as...
$10.20
WD-PHCRB
Backup Plate for Chain Retainer XL, measuring 7.75" x 7.25". Weight: 4.10 LBS
Sold individually.
$118.55
WD-FPS
Our pipe type finger dock stabilizer is an easy way to stabilize your finger dock. We use two WD-TF Single T Females, two WD-B Backup Plates, and 2" galvanized pipe. An F-PIN34 and Clip connect each end (included). Weight: 24 LBS
$13.75
WD-FDS135
Using our WD-FDS45 and WD-FDS135, you can construct a finger deck stabilizer. This assembly helps stabilize narrow fingers by spreading the load onto the main dock. The WD-B Backup Plates are used as backups to the T (not included). Weight: 4.5 LBS
Sold individually.
$23.95
WD-FDS45
Using our WD-FDS45 and WD-FDS135, you can construct a finger deck stabilizer. This assembly helps stabilize narrow fingers by spreading the load onto the main dock. The WD-B Backup Plates are used as backups to the T (not included). Weight: 8.52 LBS
Sold individually.
$62.70
WD-RP1
Ideal for those areas where a sturdy roller assembly is needed. Weight: 13.5 LBS
Sold individually.
from
$140.55
WD-BAR34 — WD-BAR56
Building a roller ramp has never been easier using our ramp roller kits. The outside roller brackets are backed up with our standard WD-E Outside Corner Ends and the center roller bracket is backed by our WD-W Washer Plates. Rollers included. The WD-BAR34 is for 3' to 4' ramps and...
$75.35
WD-SP
Splice Plates are designed to join two side stringers together to make longer dock sections. The flat plate is used on the outside of the stringer, and the T plate is used on the inside of the stringer. The T plate will attach to the cross stringer as shown. Set...
from
$129.55
WD-RCP3 — WD-RCP6
The ramp cover plates are designed to cover the gap created by the male/female hardware between the ramp and shore by providing a covered walking surface between the sections. One side is pre-punched and will bolt through the deck surface. The opposite side will slide with the movement of the...
$45.10
WD-HDF
Has three 1/2" tabs and is used with Heavy Duty Outside Corner Male (WD-HDM) or Heavy Duty Single T Male (WD-HDTM) connectors. The tabs are pre-drilled to accommodate a 3/4" pin or bolt. Use these where additional strength is needed. Weight: 9.51 LBS
Sold individually.
$39.05
WD-HDM
Has two 3/4" tabs and is used with Heavy Duty Outside Corner Female (WD-HDF) or Heavy Duty Single T Female (WD-HDTR) connectors. The tabs are pre-drilled to accommodate a 3/4" pin or bolt. These are used where additional strength is needed. Weight: 9.51 LBS
Sold individually.
$34.40
WD-HDTF
Has three 1/2" tabs and is used with Heavy Duty Outside Corner Male (WD-HDM) or Heavy Duty Single T Male (WD-HDTM) connectors. Can be bolted to the side of a dock for finger attachment. These are used where additional strength is needed. Uses a (WD-HDB) Heavy Duty Backup Plate. Weight:...
$29.15
WD-HDTM
Has two 3/4" tabs and is used with Heavy Duty Outside Corner Female (WD-HDF) or Heavy Duty Single T Female (WD-HDTF) connectors. The tabs are pre-drilled to accommodate a 3/4" pin or bolt. These are used where additional strength is needed. Uses a (WD-HDB) Backup Plate. Weight: 3.00 LBS Sold...
$7.45
WD-HDB
Heavy Duty Backup Plates are used to backup the (WD-HDTM) Single T Male and (WD-HDTF) Single T Female connectors. Weight: 2.25 LBS
Sold individually.
$39.90
WD-SM
The Special Outside Corner Male allows a finger dock to be added at a corner of a main dock. Use with standard (WD-F) Outside Corner Females. Weight: 11.75 LBS
Sold individually.
$46.50
WD-SF
The Special Outside Corner Female allows a finger dock to be added at a corner of a main dock. Use with standard (WD-M) Outside Corner Males. Weight: 11.75 LBS
Sold individually.
$39.90
WD-SMF
The Special Outside Corner Male/Female allows a finger dock to be added at a corner of a main dock. Use with standard (WD-F) Outside Corner Females and (WD-M) Outside Corner Males. Weight: 11.75 LBS
Sold individually.
$23.95
WD-TFJB
This Special Single T Female allows a female connection where a cross stringer is present on a main dock as shown in the second image to the left. Use with (WD-M) Outside Corner Males. Weight: 3.75 LBS
Sold individually.
$8.80
WD-A8
This 8" tall Angle is perfect to use with larger framing. Each 8" Angle is backed by two 8" high Washer Plates (WD-W8). Weight: 3.50 LBS
Sold individually.
$4.15
WD-W8
These 8" high Washer Plates are used with the 8" high Angles (WD-A8). The wood is sandwiched between the steel providing greater strength. Weight: 0.50 LBS
Sold individually.
$12.10
WD-A66
These longer Angles use two Backup Plates (WD-B) with each Angle to sandwich lumber and provide a solid connection. Weight: 1.75 LBS
Sold individually.
$20.10
WD-NAE
Outside Corner Ends are used at the ends of docks, ends of finger docks, or when plain ends are needed. Outside Corners are backed by (WD-NAIN) Inside Corners. Weight: 7.50 LBS
Sold individually.
$29.70
WD-NAM
Has one 3/4" tab and is used with Outside Corner Female (WD-F) or Single T Female (WD-TF) connectors. The tabs are pre-drilled to accommodate a 3/4" pin or bolt. Weight: 8.00 LBS
Sold individually.