hardware 53 Products
$17.00
WD-E
Outside Corner Ends are used at the end of docks, ends of finger docks, swim floats corners, or when plain ends are needed. Weight: 7 LBS
Sold individually.
$28.50
WD-F
Has two 2.5" tabs and is used with Outside Corner Male (WD-M) or Single T Male (WD-TM) connectors. The tabs are pre-drilled to accomodate a 3/4" pin or bolt. Weight: 8.5 LBS
Sold individually.
$47.50
WD-HDF
Has three 1/2" tabs and is used with Heavy Duty Outside Corner Male (WD-HDM) or Heavy Duty Single T Male (WD-HDTM) connectors. The tabs are pre-drilled to accommodate a 3/4" pin or bolt. Use these where additional strength is needed. Weight: 9.51 LBS
Sold individually.
$49.00
WD-SF
The Special Outside Corner Female allows a finger dock to be added at a corner of a main dock. Use with standard (WD-M) Outside Corner Males. Weight: 11.75 LBS
Sold individually.
$25.00
WD-M
Has one 1.75" tab and is used with Outside Corner Female (WD-F) or Single T Female (WD-TF) connectors. The tabs are pre-drilled to accommodate a 3/4" pin or bolt. Weight: 8 LBS
Sold individually.
$41.00
WD-HDM
Has two 3/4" tabs and is used with Heavy Duty Outside Corner Female (WD-HDF) or Heavy Duty Single T Female (WD-HDTR) connectors. The tabs are pre-drilled to accommodate a 3/4" pin or bolt. These are used where additional strength is needed. Weight: 9.51 LBS
Sold individually.
$42.00
WD-SM
The Special Outside Corner Male allows a finger dock to be added at a corner of a main dock. Use with standard (WD-F) Outside Corner Females. Weight: 11.75 LBS
Sold individually.
$42.00
WD-SMF
The Special Outside Corner Male/Female allows a finger dock to be added at a corner of a main dock. Use with standard (WD-F) Outside Corner Females and (WD-M) Outside Corner Males. Weight: 11.75 LBS
Sold individually.
from
$28.00
STF-PH3 — STF-PH5
These hot-dipped galvanized welded pipe holders bolt directly to the truss frame. Uses 3" I.D. pipe for anchoring. STF-PH3 - 3 inch - 9.7 lbs. STF-PH4 - 4 inch - 11.5 lbs. STF-PH5 - 5 inch - 16 lbs.
Sold individually.
from
$71.50
STF-PH3S — STF-PH5S
These two-piece hot-dipped galvanized welded pipe holders provide easy installation and removal of your dock. Four hex head bolt sets included. STF-PH3S - 3 inch - 18.88 lbs. STF-PH5S - 5 inch - 21.98 lbs.
Sold individually.
from
$136.50
WD-RCP3 — WD-RCP6
The ramp cover plates are designed to cover the gap created by the male/female hardware between the ramp and shore by providing a covered walking surface between the sections. One side is pre-punched and will bolt through the deck surface. The opposite side will slide with the movement of the...
from
$148.00
WD-BAR34 — WD-BAR56
Building a roller ramp has never been easier using our ramp roller kits. The outside roller brackets are backed up with our standard WD-E Outside Corner Ends and the center roller bracket is backed by our WD-W Washer Plates. Rollers included. The WD-BAR34 is for 3' to 4' ramps and...
$66.00
WD-RP1
Ideal for those areas where a sturdy roller assembly is needed. Weight: 13.5 LBS
Sold individually.
$17.50
WD-TF
Has two 1/2" tabs and is used with Outside Corner Male (WD-M) or Single T Male (WD-TM) connectors. Can be bolted to a seawall for hinging ramps or to the side of a dock for finger attachment. Weight: 3.5 LBS
$36.50
WD-HDTF
Has three 1/2" tabs and is used with Heavy Duty Outside Corner Male (WD-HDM) or Heavy Duty Single T Male (WD-HDTM) connectors. Can be bolted to the side of a dock for finger attachment. These are used where additional strength is needed. Uses a (WD-HDB) Heavy Duty Backup Plate. Weight:...
$25.50
WD-TFJB
This Special Single T Female allows a female connection where a cross stringer is present on a main dock as shown in the second image to the left. Use with (WD-M) Outside Corner Males. Weight: 3.75 LBS
Sold individually.
$14.50
WD-TM
Has one 3/4" tab and is used with Outside Corner Female (WD-F) or Single T Female (WD-TF) connectors. The tabs are pre-drilled to accommodate a 3/4" pin or bolt. Weight: 3 LBS
$31.00
WD-HDTM
Has two 3/4" tabs and is used with Heavy Duty Outside Corner Female (WD-HDF) or Heavy Duty Single T Female (WD-HDTF) connectors. The tabs are pre-drilled to accommodate a 3/4" pin or bolt. These are used where additional strength is needed. Uses a (WD-HDB) Backup Plate. Weight: 3.00 LBS Sold...
$79.50
WD-SP
Splice Plates are designed to join two side stringers together to make longer dock sections. The flat plate is used on the outside of the stringer, and the T plate is used on the inside of the stringer. The T plate will attach to the cross stringer as shown. Set...
$139.00
STF-FPS
AM Docks Pipe Type Stabilizers add stability and strength to your finger dock. Each stabilizer includes one 4' pipe (2" I.D.), two female connector plates, and two connector pins. Weight: 25 LBS
$31.00
STF-PH29
These hot-dipped galvanized welded pipe holders (with set screws) are perfect for handrail and bolt directly to the truss frame. Use 1-1/2” pipe and Quick Clamps for handrail.
Weight: 10.00 LBS
Sold individually.
from
$120.00
STF-BAR34 — STF-BAR56
Building a roller ramp has never been easier using our ramp roller kits.
The STF-BAR34 is for 3' to 4' ramps and comes with two rollers. The STF-BAR56 is for 5' to 6' ramps and comes with three rollers.
from
$263.50
STF-H3 — STF-H8
Allows additional movement for greater water fluctuation. Designed for strength, these taper truss hinge connectors provide a smooth deck surface while allowing the dock to hinge up and down. The hinge is hot-dipped galvanized to ensure maximum service. Connects with wood dock male and female hardware (WD-TM and WD-TF) STF-H3...
